Things do not end with buying and installing a new garage door in Spring Hill. The thing is, it require proper care and maintenance for them to retain their top quality and condition. In fact, even if you purchased a topnotch brand and a heavy-duty material, it is still a must that you do the right things to care for your garage door. Here are some tips on door maintenance that will help you keep the door looking and working like it is brand new and minimising the need for garage door repairs.
Garage Door Repair – Problems and Fixes in Spring Hill
Your garage should be as usable, organized, and welcoming as the rest of your home. You park your car in it. You use it for storage. You may even keep your family's bikes and sports equipment there. So it's a major nuisance when your garage door won't open properly.
Noisy garage doors are also annoying, especially if you have to leave for work early, and your entire family is woken by the squeaking.
Garage door maintenance might not be a top priority, but if you check all the working parts annually as part of a winterizing project, you'll never have to wrestle with a groaning garage door again.
What causes garage door rollers to stick?
• Dry rollers can cause the door to only open part way. Dry rollers can also make the door squeak when it's opening. The rollers must be lubricated.
• Rusty rollers can stick. The rust must be removed. If your garage is in a high-moisture environment, the rollers may be prone to rust. You can prevent rust-caused problems by replacing steel rollers with stainless steel or zinc plated ones.
• Worn rollers may create a loud, annoying popping sound when the door operates. These rollers must be replaced.
• Loose weatherstripping could jam against the sides of the door, and make it stick. It must be fixed.
How to fix and maintain garage door rollers
• Soak stuck rollers in kerosene. Use an old toothbrush to work the kerosene into all the parts. Wipe all the parts clean with a cloth.
• Scrub rusty rollers with steel wool to remove any rust. Wipe flecks of rust away.
• Lubricate dry rollers by applying WD-40 or 3 in 1 motor oil to the rollers, tracks, and hinges
• Tighten all screws and bolts which many have been vibrated loose over time.
How to replace garage door rollers
1. Open your garage door completely. Disconnect the door from your power opener. Unplug the garage door opener for safety.
2. Place a clamp on the track about 2/3 of the way up the door opening.
3. Bend the track slightly open with pliers.
4. Line up the first old roller with this opening. Wedge a screwdriver between the roller and the track, and pry the old roller out of the track. Remove this old roller.
5. Insert a new roller into the track.
6. Roll the door down to the next roller, and repeat these steps for the bottom rollers.
7. Bend the track back into alignment and roll the door all the way open.
8. Bend a section of the track in the middle of the overhead section with pliers. Make sure the door does not slip from the track and hit you.
9. Pry out and replace the last roller.
10. Bend the track back into shape with the pliers.
11. Remove the clamp from the track.
12. Plug the door opener back in, and reattach it to the door.
13. Close the door, watching for misalignment of the track. Adjust the bolts if needed.
Garage Door Installation - Successfully Assembling the Garage Door Parts
My garage door will not open. What could be the problem?
1. Checking the springs on your garage door is the first thing you must do. On a sectional door, the springs are located on the header, above the door. Look for the long torsion tube that spans the width of the door, the springs should be right in the middle. Some doors can have up to 4 springs per door. To know your spring is broken, you will need to look for a crack in the coil or if the spring is sagging, you will know it needs to be replaced.
On a one piece door, the springs are easily visible on the side of the garage door. Make sure they are attached properly to the hinges and not hanging loose.
NEVER OPERATE A GARAGE DOOR WITH A BROKEN SPRING! If you have found that your spring is broken, call a local garage door technician to service it for you. Please note that when you replace a spring, you should replace all of the springs for that door.
2. The next thing you want to do is to check to see if your slide lock engaged or trolley lock (the red cord that hangs down from the motor rail) has been disengaged. The side locks are located on the insides of the garage door on one or both sides of the door. The trolley lock, or emergency release lock, is located on the motor rail. To reengage this motor, pull the red cord up and towards the door you will hear it latch into place and see that it is in a different lock position. Once the latch is pulled, the motor will become operable. If you want to disengage motor because your motor is broken pull down on the red cord trolley release.
3. The third thing you can do is to check your cables. The door cables are located on each side of the door and are connected to the torsion tube. Does the cable look like it is out of sync or not wound up correctly? Another easy way you can tell your cable is broken is that your door will look crooked in the opening.
4. The last thing you can do is to see if you have power going to your motor. It is quite common to have a fuse in your circuit breaker go bad. If your motor is not operating at all when you click on the wall button or your portable remotes, this might be the problem. Check your circuit breakers, plug another source into the outlet and if needed call an electrical technician.
Repairing a Garage Door