Things do not end with buying and installing a new garage door in Kenmore Hills. The thing is, it require proper care and maintenance for them to retain their top quality and condition. In fact, even if you purchased a topnotch brand and a heavy-duty material, it is still a must that you do the right things to care for your garage door. Here are some tips on door maintenance that will help you keep the door looking and working like it is brand new and minimising the need for garage door repairs.
Garage Door Repair – Problems and Fixes in Kenmore Hills
There's a feeling of utter joy that comes over anyone that pushes a garage door opener. Like magic, the steel mammoth glides open and greet us with a promise of security and storage. But what happens when the opener breaks down? Luckily, garage door openers are relatively easy to fix and low maintenance!
In this article we'll show you step by step, the ways in which to get it back up and running in no time. An opener consists of an electric motor which lifts the mechanism at the push of a button. These devices can be wired into the electrical circuit, or used in combination with a battery powered remote: most systems have both. When pushed, the button sends an infrared signal to the control unit that, in turn, tells the motor to get to work.
Many various types of problems can occur:
1. The opener fails to respond.
2. The door may raise but fails to close.
3. The motor may run, but not open the garage.
4. The motor may run without any command at all!
5. The system may not open or shut completely
6. The motor may reverse when closing.
Due to the fact that these devices are little more than electronic controls and a motor, the majority of the servicing you can do starts with battery replacement, motor tests, and the lubrication and alignment of the mechanisms.
Identifying and Fixing the Issue:
1. In the case of the system being non-responsive, make certain the cord is properly plugged into a secured and operational electrical receptacle. Wait roughly 15 minutes and try again.
2. If the unit operates by remote by fails to work when used with the hard wired button, look for loose connections or damaged wires. If this is found, you may need to call an electrician.
3. If the opener runs but does not open the door, look for wear of the chain drive sprocket or worm gear, and if needed have the parts professionally look at.
4. If the unit operates by itself, check to see if the button on the remote has become stuck. If this is not the case, you may be looking at a faulty circuit board which may need to be replaced.
Chances are you just may find yourself in over your head. In such case, it's always recommended that you consult a professional technician as a way to help you avoid a more costly repair down the road. Though, hopefully with the above tips in hand you'll be able to successfully diagnose and treat your automatic door issues. Best of luck!
How to Repair a Garage Overhead Door
If your garage overhead door has become loose in it's tracks or seems heavier to lift than it used to be, you may well be correct. Door hinges and rollers wear out over time and become sloppy. Adding grease may help for a short period but in the end you will have to replace some of the door parts. Basically there three types of hinges used. They are stamped #1, #2 and #3's. When you look at your door you will notice that at the top and bottom are two roller brackets that are different from the rest of the hinges on the door listed above. The bottom roller bracket also has a protruding peg where the spring cable is attached. The top bracket projects further out from the door then the rest of the rollers to allow the door to when opened, immediately follow the curved section of the track without binding. A word of caution. Never remove the bottom bracket without first disconnecting the lift spring and cable when the door is open. If the cable is removed from the bottom roller bracket with the door closed, the spring will recoil with no control and can cause a serious injury.
Before removing any hinges, close the door and place two C-clamps or Vise grips in both tracks just at the top of the door to prevent any movement if the lift springs are still connected. You may by removing one hinge at a time (not the bottom roller bracket), replace each hinge one by one in the exact position where it was removed. Purchase roller grease made for overhead door rollers and apply a liberal amount of grease to each roller as it is installed. Remind yourself to do this once a year as maintenance.
Once all the hinges are replaced take a good look at the door itself to assure that all the panels are in sound condition, all glass is unbroken and any other bolts or screws at the lift or foot handles for example are in place and are tight. If the bottom weather seal is broken or missing, replace that as well. Finish the door with a new coat of paint it needs it.
Remove your c-clamps and raise the door to the full open position. This will take all the tension out of the lift springs. If you do not know what "weight" your door springs are, most springs are spray a painted color on one end. Red, yellow, white and so on. Each color indicates what weight door it should be used on. Wood doors are very heavy and usually use the heaviest spring available. Aluminum doors, the lightest springs and so on. Carefully remove one side of the door's spring and cable. Check the cable pulley to assure it is not split or worn. Replace the spring, pulley and cable in the exact same manner in which is was removed. If in doubt, look at the one you have not removed as yet. Once both springs are replaced operate the door a number of times placing some extra grease in the tracks for the rollers to spread.
Your garage door should by much quieter to operate and much easier to lift and close. If you intend to install an electric garage door opener, these maintenance items are a must before you do the installation.
Garage Door Maintenance - Some Indispensable Tips to Remember