Graceville Commercial Garage Door Repair

Things do not end with buying and installing a new garage door in Graceville. The thing is, it require proper care and maintenance for them to retain their top quality and condition. In fact, even if you purchased a topnotch brand and a heavy-duty material, it is still a must that you do the right things to care for your garage door. Here are some tips on door maintenance that will help you keep the door looking and working like it is brand new and minimising the need for garage door repairs.

Garage Door Repair Cables

Garage Door Repair РProblems and Fixes in Graceville

It can be overwhelming to walk into the garage and see the mess that has been accumulated over time if your space has been used as a dumping garage instead of being utilized as a parking space and as an additional storage area. What can be even more mind boggling than the mess itself is how to go about fixing it.

There are numerous companies in the garage design space that can help make the process a little easier and eve more customizable to meet your need. Garage Tek is one of the leaders in the field for garage storage systems and offer design and installation services, freeing you from the entire ordeal.

The process starts with a free consultation at your house where a consultant will review with you what they can do to give you additional storage space in your garage and what type of items they offer. The next step is for the consultant to conduct a thorough investigation of the garage, which includes checking the walls, ceiling as well as taking measurements for design specifications.

Now comes the easy part. It is time to let the representative know what your needs are and what are your wants. They are the experts in the field and will be able to work with your to make your vision become a reality. To help them do that, they use proprietary software that allows you to choose the right products and layout to get the most out of your garage space.

After the design part is over, they handle all of the installation themselves. This includes the removal of other items that may be currently on your garage walls, such as shelves, nails or cabinets. Having an experienced installer working on the job means they will be able to deal with any type of garage, whether it is bare studs to concrete walls to any other type of material you may have.

In addition to taking care of the installation and improving your storage space, they polish the room off with floor tiles to give the garage floor some pop plus extra durability.

Garage Door Repair Cables

Garage Storage Systems With Garage Tek

IMPORTANT NOTE: READ THIS WHOLE GUIDE BEFORE STARTING!

This is a D.I.Y. guide and can be performed by any one providing you have the correct tools:

1. 4mm Pin Punch.
2. Mole Grips.
3. Cable cutting tool such as snips or pliers.
4. Hammer.
5. Screwdrivers.
6. Set of steps.

To begin, if only one cable has snapped you will need to cut the cable on the other side to allow you to be able to replace both sides. If you still have tension in the spring then put the c-clip into the whole in the shaft to the left of the right hand side cone.

This should be supplied with your cones and cables repair kit.

Once this is in place you can cut the intact cable.

After cutting the cable you will need to climb up your steps and locate the 4mm pin which holds the cone in place on the shaft. When you have located this (you may need to rotate the shaft slightly to get access) take your hammer and 4mm pin punch and knock the pin all the way through and into the timber frame. I recommend you spray the end of the punch with some WD40 or similar so it is easier to pull back out when the pin is removed.

If the door is fitted between the opening then it is likely you will have to loosen the gear from the top of the frame to allow you to pull the cone from the shaft.

IMPORTANT: You MUST do one side at a time!

When you have the cone free, replace it with the new one and be sure to take the old pin out of the timber frame if it has jammed into it as it will be in the way if you do not! Don't replace the pin yet, leave the cone loose.

Refit the gear to the the frame.

Now go over to the other side and do the same.

Fitting the cable onto the pivot point.

When fitting the cable into the pivot point it is important to have the cables in the correct position otherwise the door will not open at all.

To do this put the pivot point through the loop. TIP: An easy way to do this is to unscrew the guide or runner and move it to one side, put the cable around the pivot point and re-fix the guide.

When done there will be some slack cable. Go back up to the cone and turn it towards you so that the slack cable wraps around the cone. When you have taken up the slack the the holes in the shaft and cone should match up. You can then knock the pin in. TIP: You may find it easier to knock the pin partially into the cone before taking up the slack cable as you will need to keep pulling the cone toward you until the pin is in. Alternatively, have an assistant hold the tension on the cone whilst you knock in the pin - be careful not to hit your assistants fingers with the hammer!

Now do the same on the other side.

If this is done correctly the left hand side pin should be at the 10 O'clock position and the right hand side should be at 2 O'clock.

The C clip can now be removed and the door should run up and down.

If the door is difficult to lift then you will have to put more tension on the spring. All up and over doors with cones and cables operate under the same principle but often there are slight differences from manufacturer to manufacturer but essentially you need to do the following:

About 2 feet in from the left hand side you will see a collar attached to the spring. This collar holds the spring tension to the centre shaft. If the collar has a nut type end then you should be able to hold the tension whilst undoing the screw(s) with an Allen Key. Once you have the spring under tension you then rotate the spring away from you (upwards). Depending on how much tension has been lost will depend on how many turns you need to give the spring. Generally speaking one movement is half a turn. Use a screwdriver or similar in the holes provided in the collar to rotate the spring. When the spring feels like it has gone as tight as it can go, hold the tension whilst tightening up the Allen Screws. Test the door slowly up and down. If it will not go all the way up without the cables going slack then you need to put more turns on the spring.

Finally, lubricate the guides and spray oil onto the spring also, this will help to keep any squeaking down and allow the door to move more freely.

You should allow a couple of hours to do this, although it can be done much quicker if the pins come out easily.

Garage Door Repair Commercial

Graceville

How to Choose a Garage Door Repair Company?


Brisbane Repair Garage Door Panel