Fig Tree Pocket Automatic Garage Door Repair

Things do not end with buying and installing a new garage door in Fig Tree Pocket. The thing is, it require proper care and maintenance for them to retain their top quality and condition. In fact, even if you purchased a topnotch brand and a heavy-duty material, it is still a must that you do the right things to care for your garage door. Here are some tips on door maintenance that will help you keep the door looking and working like it is brand new and minimising the need for garage door repairs.

Garage Door Repair Business

Garage Door Repair – Problems and Fixes in Fig Tree Pocket

The garage door is often the part of the house that most people forget to maintain. It is easy enough to remember to cut the grass when it tickles your knees as you walk into your house, but you may have trouble remembering to take care of your garage door until you are trying to park your car and it just will not open. Worse yet, you may not know there is a problem until there are holes in some of the panels. But with a few simple practices you can keep your garage door in great shape to protect your car and tools.

To prevent any long term damage to moving parts on your door it may be a good idea to lubricate the moving parts from time to time. Spray all the hinges, rollers, and tracks with a little WD-40 to keep things moving freely. It may even be a good idea to spray the moving pieces of the lock to make sure it isn't rusting up. If you are the type of person that normally doesn't park their car in the garage then you may be in more danger of this than someone who opens and closes the door frequently.

For wooden garage doors you need to make sure that both sides of the panels are painted. This helps to shield the door from humidity and frequently changing temperatures that can lead to rotting. If your door is rotting through then you are not shielding your possessions from the elements. You may also want to make sure that you are not keeping any caustic liquids or paint thinners near the door, as the slow leaks that often happen in these containers may lead to damage to the paint.

If you have a medal door you still need to make sure that the paint job on your garage door is intact. The paint helps protect the door from rust, which can cause holes or the moving parts to lock up. But whether you have a medal or wooden door it is important to make sure that you keep the door clean. Excessive dirt may eventually wear away at the paint job, or get into the moving pieces and cause damage over time. You should use a mild cleaner to wash the door, as something caustic may damage the paint job faster than the dirt. Dish soap or any kind of soap you would use to wash your car will do well to protect the paint job.

Also important to check from time to time is the spring tension. The springs that help lift your door up and down can wear out from the weight of the door it is constantly lifting up and setting down. If the door feels too heavy when you open it, or if it sounds like your motor is struggling with the weight of the door than it may be time to change the springs. Use caution because these springs are kept under constant tension and can be dangerous if not removed properly. If you are not sure how to do this then you may want to call a professional.

Just remember to protect your garage door so it can continue to protect your things in return. With a little attention your door can last for years to come.

Sears Garage Door Repair Phone Number

Garage Door Opener Repairs

IMPORTANT NOTE: READ THIS WHOLE GUIDE BEFORE STARTING!

This is a D.I.Y. guide and can be performed by any one providing you have the correct tools:

1. 4mm Pin Punch.
2. Mole Grips.
3. Cable cutting tool such as snips or pliers.
4. Hammer.
5. Screwdrivers.
6. Set of steps.

To begin, if only one cable has snapped you will need to cut the cable on the other side to allow you to be able to replace both sides. If you still have tension in the spring then put the c-clip into the whole in the shaft to the left of the right hand side cone.

This should be supplied with your cones and cables repair kit.

Once this is in place you can cut the intact cable.

After cutting the cable you will need to climb up your steps and locate the 4mm pin which holds the cone in place on the shaft. When you have located this (you may need to rotate the shaft slightly to get access) take your hammer and 4mm pin punch and knock the pin all the way through and into the timber frame. I recommend you spray the end of the punch with some WD40 or similar so it is easier to pull back out when the pin is removed.

If the door is fitted between the opening then it is likely you will have to loosen the gear from the top of the frame to allow you to pull the cone from the shaft.

IMPORTANT: You MUST do one side at a time!

When you have the cone free, replace it with the new one and be sure to take the old pin out of the timber frame if it has jammed into it as it will be in the way if you do not! Don't replace the pin yet, leave the cone loose.

Refit the gear to the the frame.

Now go over to the other side and do the same.

Fitting the cable onto the pivot point.

When fitting the cable into the pivot point it is important to have the cables in the correct position otherwise the door will not open at all.

To do this put the pivot point through the loop. TIP: An easy way to do this is to unscrew the guide or runner and move it to one side, put the cable around the pivot point and re-fix the guide.

When done there will be some slack cable. Go back up to the cone and turn it towards you so that the slack cable wraps around the cone. When you have taken up the slack the the holes in the shaft and cone should match up. You can then knock the pin in. TIP: You may find it easier to knock the pin partially into the cone before taking up the slack cable as you will need to keep pulling the cone toward you until the pin is in. Alternatively, have an assistant hold the tension on the cone whilst you knock in the pin - be careful not to hit your assistants fingers with the hammer!

Now do the same on the other side.

If this is done correctly the left hand side pin should be at the 10 O'clock position and the right hand side should be at 2 O'clock.

The C clip can now be removed and the door should run up and down.

If the door is difficult to lift then you will have to put more tension on the spring. All up and over doors with cones and cables operate under the same principle but often there are slight differences from manufacturer to manufacturer but essentially you need to do the following:

About 2 feet in from the left hand side you will see a collar attached to the spring. This collar holds the spring tension to the centre shaft. If the collar has a nut type end then you should be able to hold the tension whilst undoing the screw(s) with an Allen Key. Once you have the spring under tension you then rotate the spring away from you (upwards). Depending on how much tension has been lost will depend on how many turns you need to give the spring. Generally speaking one movement is half a turn. Use a screwdriver or similar in the holes provided in the collar to rotate the spring. When the spring feels like it has gone as tight as it can go, hold the tension whilst tightening up the Allen Screws. Test the door slowly up and down. If it will not go all the way up without the cables going slack then you need to put more turns on the spring.

Finally, lubricate the guides and spray oil onto the spring also, this will help to keep any squeaking down and allow the door to move more freely.

You should allow a couple of hours to do this, although it can be done much quicker if the pins come out easily.

Garage Door Opener Repair Man

Fig Tree Pocket

Garage Door Openers - Confusing Choices, But Convenient Luxuries Simplified For the Home Owner


Brisbane Repair Garage Door Panel