Things do not end with buying and installing a new garage door in Doolandella. The thing is, it require proper care and maintenance for them to retain their top quality and condition. In fact, even if you purchased a topnotch brand and a heavy-duty material, it is still a must that you do the right things to care for your garage door. Here are some tips on door maintenance that will help you keep the door looking and working like it is brand new and minimising the need for garage door repairs.
Garage Door Repair – Problems and Fixes in Doolandella
Have you grown tired of that rusty or rotted garage door that never seems to work quite the way it should? If you're in need of some serious repair or maintenance, but don't want to pay a professional to do the work for you, then perhaps you can do the work on your own. Installing a new system on your own is definitely possible and only requires a few tools and the right knowledge. Within a few hours you can give a brand new look to your home.
The following steps will provide you with the basics of installing a pre-hung garage door. Remember, it's important that you maintain safety while performing this task, and always consult the instruction manual if any questions ever arise.
Position The Bottom Panel In The Doorway
Install weatherstripping on the bottom panel and position the panel in the doorway. Temporarily hold the panel in place by tapping nails through either side of the panel brackets into the door jamb. When the panel is in place, attach hinges to the upper edge of the panel.
Install The Tracks
After locating the first panel in the proper place, install the tracks for the garage door according to the instructions which should be found in the instruction manual.
When the tracks have been set in place, install the rollers and any remaining brackets that either are to be installed onto the door itself or the wall frame, so that the door panels may be set into place.
Install The 1st Panel
Position one side of the panel into the tracks, and do the same for the other side.
Install The 2nd Panel
Prepare the second garage door panel by installing the rollers where necessary. When ready, lift the panel into place and insert the rollers into the tracks. You will want to get help from another person for this step.
Install the 3rd Panel
Prepare the third panel by installing the rollers as well as any brackets that are needed. Lift the panel into place and insert the rollers for this panel into the tracks. When the panel is in place, make sure the vertical tracks are fully fastened to the garage wall using lag bolts that are provided with the package At this point, make sure the door is level and the tracks are plumb.
Attach Jamb Brackets
Attach the jamb brackets and fasten them to the wall, ensuring that the lag screws are drilled into the solid framing boards for security.
Install Top Tracks
Install the curved and horizontal portions of the tracks according to the specifications set forth in the user manual. Be sure to rest the horizontal tracks on top of something so they do not swing free or fall down.
Install The Track Hanger
Check to see that the horizontal track is completely level. Attach the hanger mounting bracket to the ceiling in a solid position where the lag screws can be drilled into framing boards. Install one end of the hanger to the mounting bracket and then line up the hanger with the horizontal garage door track. Trim the hanger and then fasten the horizontal track to the hanger. Repeat this process on the other side with the other horizontal track section.
Install The Last Door Panel
When the horizontal track sections are in place, install the final door panel.
Install Torque Tube Or Tension Springs
If the garage door you are installing comes with a torque tube, you can install it according to the manufacturer specifications. If your garage door uses tension springs, you may need to call a professional because special tools are required to obtain the proper tension. Improperly installed springs can be a safety hazard for both property and people. When in doubt, call the professional.
If you have the right tools and the knowledge to complete the task, you can install that new system and give your home a new face lift.
What Are Roller Garage Doors?
You'd be right to be concerned about security with your wireless garage door opener and remote. An intruder can gain access to your garage contents, or even your home if you don't follow some simple security steps.
Different radio frequencies are used for communication between the remote and the opener. Tiny switches known as dip switches are used to adjust the frequency used between the two. It is a wise idea to reconfigure the dip switch settings to make sure your garage more secure.
A dip switch is a small block of plastic about the size of a dice cut in half. They are usually colored blue or red with 8 to 10 tiny white switch levers positioned up or down. Only when the up / down switch patterns match on both devices will your garage door opener remote control be able to communicate with the opener unit. By adjusting the switch pattern, you are changing the radio frequency used to communicate between the two.
You should be able to easily locate the dip switch on the opener and on the remote control clicker. But to get access to the dip switch on the remote you might need to open it up if the dip switch isn't found in the battery compartment. Remove the screws holding the remote together, or carefully pry it apart if there are no screws. Once you have access to the dip switch on the remote, scramble the switch positions, and then match the positions on the openers dip switch block. It does not matter what the pattern looks like, so long as its a random pattern that would be difficult for someone to guess.
If you have trouble getting the remote to work after doing this, verify that the dip switch patterns are the same on both units. Then check the remote battery is in good condition, and as usual, make sure the opener has power, and operates normally using the control panel inside your garage. You might have to read the manual if all else fails.
If you are thinking of getting a new garage door opener or have already gotten one, then you will want to change settings, just to make sure everyone is honest. Don't forget, your installer or anyone working with him knows your frequency switch settings unless you change them. So go ahead and mix up the switch pattern settings and test that it works.
Even if you are a garage door opener installation do-it-yourself type, you'll want to make the same changes. Don't just stay with the factory default settings. If you did, then anyone could just drive down your street with a compatible remote until he finds a door that opens and gives access to your home. Make sure that's not you.
This advise also applies to anyone buying or renting a new home too. Just like you might change the lock to guarantee there are no spare keys floating around that could compromise your home security. You have no way of knowing how many previous residence there might have been. And you wouldn't want someone to just walk right into your garage or home.
How to Cook Barbeque Ribs