Carina Heights Garage Door Emergency Repair

Things do not end with buying and installing a new garage door in Carina Heights. The thing is, it require proper care and maintenance for them to retain their top quality and condition. In fact, even if you purchased a topnotch brand and a heavy-duty material, it is still a must that you do the right things to care for your garage door. Here are some tips on door maintenance that will help you keep the door looking and working like it is brand new and minimising the need for garage door repairs.

Automatic Garage Door Opener Repair

Garage Door Repair – Problems and Fixes in Carina Heights

While automatic garage door openers can be extremely useful and convenient they can also become a burden when not working properly. Here are a few tips and pointers to help keep your door opener in tip top shape, or help you determine the solution to fixing a malfunctioning one. However, since all garages are different and operate in many ways, be sure to consult your owners manual or professional repairman for more help if needed.

Maintenance

The first step to a properly functioning door is to properly maintain its many moving parts. Here are four simple and effective ways to ensure years of use:

  • Yearly Inspections: The best and most effective way to solve a problem is to prevent it. Be sure to inspect your door and electric motor for anything that seems out of the ordinary. Loose and worn hinges, tired springs, and wobbly nuts and bolts are some common issues that may arise. Be sure to address any potential problems before they worsen and create additional, more complex problems.
  • Paint and Stain: Be sure to keep your garage door properly painted and stained. What most homeowners do not realize is that this step includes both the inside and outside of your door. Only painting the exterior door can weaken the paint through moisture, causing your door to warp.
  • Lubrication: The many moving parts must be kept lubricated, especially the rollers and hinges that allow the door to bend and move smoothly. Apply a low viscosity, permeating oil such as WD-40, PlusGas, Liquid Wrench, PB Blaster, Mouse Milk, Unilease, GT85, Kroil, or CRC 5-56 at least once a year.
  • Watch the Door Tracks: The tracks that guide the door must be kept in proper alignment to effectively guide the rollers. If the track needs adjusting, loosen the support bolts and use a hammer and small wood block to return it to its correct position.
Troubleshooting and Repair

Several problems can arise in your garage door or opener because of their many parts and exposure to weather. The most common problems can usually be fixed fairly easily, but since garage doors differ, be sure to check your owners manual to ensure proper repair.

One of the most common problems can be that the door becomes difficult to open and close. This problem could potentially be with the electric opener, in which case you should address your owners manual. The simple way to check this is to pull the release cord that often dangles below the opener to raise the door manually. If it works fine when you do this, then the problem is most likely with the electric opener. If the door seems exceptionally heavy, the problem could be spring tension. Do not try to adjust the spring tension yourself as they are under extreme amounts of pressure and can be dangerous to adjust, call a properly certified repairman instead.

If your house is fitted with a swing-up, one piece door that is sagging in the middle when it is raised, you or a repairman can install metal reinforcing rods across the center of the interior door.

If your door does not open completely but only opens 4 or 5 feet, the limit adjustment screw should be adjusted according with the owner's manual. If the door does not close entirely, the adjustment screw needs to be manipulated as well. Refer to your owners manual for the placement of these screws on your model of opener.

Most problems with doors and openers can be solved relatively simply with a few adjustments every few months, and can be prevented with simple maintenance. If the proper steps are taken, garage doors should last more than 20 years, and garage door openers should last at least 10, but small steps like those described above can make a big difference.

Stanley Garage Door Repair

The Best Garage Door Repairs

IMPORTANT NOTE: READ THIS WHOLE GUIDE BEFORE STARTING!

This is a D.I.Y. guide and can be performed by any one providing you have the correct tools:

1. 4mm Pin Punch.
2. Mole Grips.
3. Cable cutting tool such as snips or pliers.
4. Hammer.
5. Screwdrivers.
6. Set of steps.

To begin, if only one cable has snapped you will need to cut the cable on the other side to allow you to be able to replace both sides. If you still have tension in the spring then put the c-clip into the whole in the shaft to the left of the right hand side cone.

This should be supplied with your cones and cables repair kit.

Once this is in place you can cut the intact cable.

After cutting the cable you will need to climb up your steps and locate the 4mm pin which holds the cone in place on the shaft. When you have located this (you may need to rotate the shaft slightly to get access) take your hammer and 4mm pin punch and knock the pin all the way through and into the timber frame. I recommend you spray the end of the punch with some WD40 or similar so it is easier to pull back out when the pin is removed.

If the door is fitted between the opening then it is likely you will have to loosen the gear from the top of the frame to allow you to pull the cone from the shaft.

IMPORTANT: You MUST do one side at a time!

When you have the cone free, replace it with the new one and be sure to take the old pin out of the timber frame if it has jammed into it as it will be in the way if you do not! Don't replace the pin yet, leave the cone loose.

Refit the gear to the the frame.

Now go over to the other side and do the same.

Fitting the cable onto the pivot point.

When fitting the cable into the pivot point it is important to have the cables in the correct position otherwise the door will not open at all.

To do this put the pivot point through the loop. TIP: An easy way to do this is to unscrew the guide or runner and move it to one side, put the cable around the pivot point and re-fix the guide.

When done there will be some slack cable. Go back up to the cone and turn it towards you so that the slack cable wraps around the cone. When you have taken up the slack the the holes in the shaft and cone should match up. You can then knock the pin in. TIP: You may find it easier to knock the pin partially into the cone before taking up the slack cable as you will need to keep pulling the cone toward you until the pin is in. Alternatively, have an assistant hold the tension on the cone whilst you knock in the pin - be careful not to hit your assistants fingers with the hammer!

Now do the same on the other side.

If this is done correctly the left hand side pin should be at the 10 O'clock position and the right hand side should be at 2 O'clock.

The C clip can now be removed and the door should run up and down.

If the door is difficult to lift then you will have to put more tension on the spring. All up and over doors with cones and cables operate under the same principle but often there are slight differences from manufacturer to manufacturer but essentially you need to do the following:

About 2 feet in from the left hand side you will see a collar attached to the spring. This collar holds the spring tension to the centre shaft. If the collar has a nut type end then you should be able to hold the tension whilst undoing the screw(s) with an Allen Key. Once you have the spring under tension you then rotate the spring away from you (upwards). Depending on how much tension has been lost will depend on how many turns you need to give the spring. Generally speaking one movement is half a turn. Use a screwdriver or similar in the holes provided in the collar to rotate the spring. When the spring feels like it has gone as tight as it can go, hold the tension whilst tightening up the Allen Screws. Test the door slowly up and down. If it will not go all the way up without the cables going slack then you need to put more turns on the spring.

Finally, lubricate the guides and spray oil onto the spring also, this will help to keep any squeaking down and allow the door to move more freely.

You should allow a couple of hours to do this, although it can be done much quicker if the pins come out easily.

Garage Door Repair Companies

Carina Heights

Sliding Garage Doors, And Why You Might Want One


Brisbane Repair Garage Door Panel